|
| Woodcraft 50mm Clip-ons |
Note that this model clip-on is NOT for the 2006-2007 GSXR600 or GSXR750 - these bikes use a 50/48 tapered clip-on. Order 12-0350 for the 2006-2007 GSXR600 or GSXR750. |
| |
| Item no.12-0150 |
Retail: $149.99(PLUS shipping) |
| Today$145.95 |
|
|
|
|
| Application Chart |
Diagrams |
Application
Notes |
|
| 2003 Honda CBR 1000 RR |
|
|
| 2004 Honda CBR 1000 RR |
|
|
| 2005 Honda CBR 1000 RR |
|
|
| 2006 Honda CBR 1000 RR |
|
|
| 2005 Suzuki GSX-R 1000 (K5) |
|
|
| 2004 Suzuki GSX-R 600 (K4) |
|
|
| 2005 Suzuki GSX-R 600 (K5) |
|
|
| 1996 Suzuki GSX-R 750 (T) |
|
|
| 1997 Suzuki GSX-R 750 (V) |
|
|
| 1998 Suzuki GSX-R 750 (W) |
|
|
| 1999 Suzuki GSX-R 750 (X) |
|
|
| 2000 Suzuki GSX-R 750 (y) |
|
|
| 2001 Suzuki GSX-R 750 (K1) |
|
|
| 2002 Suzuki GSX-R 750 (K2) |
|
|
| 2003 Suzuki GSX-R 750 (K3) |
|
|
| 2004 Suzuki GSX-R 750 (K4) |
|
|
| 2005 Suzuki GSX-R 750 (K5) |
|
|
|
|
|
|
|
|
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: what size clip ons and triple clamp do i need on stock 2001 ducati monter 600 |
| ANSWER: 50mm. If you have fitment questions, go to the Woodcraft website and click on the riser fitment guide - it will answer all of your questions. You can then come back here to purchase whatever you need. |
|
| QUESTION: I bought a set of 06 750 gsxr forks off ebay. i have my old 97 600 gsxr clip ons still. will they transfer over? if not what size do i need? |
| ANSWER: They will not work. Your 97 600 has 45mm forks on it and the newer models are 50mm. If you are running the bike at the stock ride height (of the 06) then you will need the stepped 50/48mm clamps. If you are raising the front you will need straight 50mm clamps. |
|
| QUESTION: I have an 06' 750. I know its the 48/50 I need to go with, my question is i'm trying to find the clip on with a 2" riser. Do you guys have this? I would prefer woodcraft, but if its not available, I will take what I can.
|
| ANSWER: The 2 inch riser may be a tight fit on the 06 GSXR750. You should go to this link to get all the information:
https://www.woodcraft-cfm.com/Assets/Products/Instructions/Clipon%20Risers.pdf
The GSXR's only have 25mm's worth of 50mm tube before it tapers down to 48mm. Our clipons need a bare minimum of 30mm. The simple solution to this is to push the forks down in the clamps by 5mm (raising the front end). This gives the bike more trail, which is what most racers do on this bike anyway (many aftermarket companies actually make parts to that the front can be raised up 10-15mm on this model). Once this is done, standard 50mm risers work perfectly. YOu just need to determine how much rise the bike can utilize. |
|
QUESTION: I am trying to put a set of clip on handle bars on a Harley Davidson that has 49mm fork tubes
Question:
will these fit on a 49mm for tube?
Answer:
These will not work on a 49mm fork. What bike are you trying to mount them on? |
| ANSWER: You can puchase a set of 48mm and have them milled out to 49mm for an additional $40 from Woodcraft. 1" Harley bars are also available for an additional $30. |
|
| QUESTION: will these fit on a 49mm for tube? |
| ANSWER: These will not work on a 49mm fork. What bike are you trying to mount them on? |
|
| QUESTION: Hello I am lowering my 07 gsxr 750 3" in the rear and want to match in the front, but the fork tube will only allow about a 2.5" drop with the triple clamp which leaves the clipons not able to clamp down. What is the diameter of the fork tube at this point and what clipons do I need to order? Thanks Playboy-Johnny. |
| ANSWER: They are 48.1mm down there. You can get away with a 48mm clipon - you'll have to gently tap it on, but that will work.... 0.1mm is a very small amount. |
|
| QUESTION: What is the internal diameter of the handle bar tubes? Would want to fit bar end mirrors etc.. |
| ANSWER: .625 inches |
|
| QUESTION: Hi, will 50 mm clip ons fit a 06 R6. |
| ANSWER: Yes it takes 50mm as long as its not an R6S those take a 43mm. |
|
| QUESTION: will these fit an '07 R1 |
| ANSWER: Yes, they will fit. In order to retain your stock steering damper you need to purchase a 50mm fork clamp as well. |
|
| QUESTION: What size do i need for a 97 gsxr 750 srad? thanks |
| ANSWER: 50mm |
|
| QUESTION: will this size fit an 01 honda 929rr |
| ANSWER: Yes, the forks on that bike are 50mm |
|
| QUESTION: I noticed that the clip on chart suggests that 2006 Truimph Speed Triple uses 50mm clip ons,...but I just measured mine with a caliper and the Outer Diameter of the Fork Tube is almost exactly 52mm. I assume that the diameter that the chart is referring to is the OD of the fork or the gripping ID of the clamp...correct? If so, I think that your chart is incorrect...
I have seen other sites that suggest 53mm is the right size for my bike...I would assume that I should use 52mm bars on 52mm forks, or is it typical to go one size larger??
Also, do all Woodcraft Clip-ons have two piece clamps for easy installation?
Thank You for your time...
Marty |
| ANSWER: 52mm is correct - the application chart for the Speed Triple is not correct. All Woodcraft clamps are 2 piece. |
|
| QUESTION: Hi Huys.
Have a ZX6RR '04 stated but 12 month '03 built date on the compliance plate. Will these clipons fit. I do not have the USD forks but the gold '03 ones fitted. |
| ANSWER: All the upside down forks for the ZX6r's have been 50mm....you're all set. |
|
| QUESTION: Ok, im assuming 7 degrees is the angle that the bar slopes down, as in, the angle to the horizontal.
but how do u adjust the angle that the bars open at, like flat/180 degrees like a BMX vs, whatever angle a sportbike comes angled back at? |
| ANSWER: You simply secure them at the angle you desire.....very straightforward. |
|
| QUESTION: The top portion of the 2002 gsxr 750 fork tube has a different diameter than the widest main body of the tube, do these fit the largest diameter section of the tube, or the smaller top section of the inverted fork?
If so what diameter would i need for the widest part of my fork? |
| ANSWER: FOr your bike, regular 50mm clipons are what you need. |
|
| QUESTION: I have an '07 Ducati S4Rs with the Ohlins Road & Track front fork. Will the 50mm clip-ons that fit the Monster S2R and S4R with Showa forks also fit my bike? |
| ANSWER: If you only changed the forks - the clipons should still work. Just be sure that there is enough clamping area for the clipon. |
|
| QUESTION: will these fit on a standart R6 2005 model,
and what is the angle of the clip on? |
| ANSWER: Yes, they will - the clipons are 7 degrees. |
|
| QUESTION: WILL THIS FIT ON A 00 GSXR 750? |
| ANSWER: Yes it will |
|
| QUESTION: will these fit my 2001 yamaha yzf R1 and i use my bike for street riding and how much will it cost to send to antigua |
| ANSWER: |
|
| QUESTION: Will these fit on a CBR 954 RR, if not what size will fit?...Thanks, EE |
| ANSWER: This is the correct size for the forks for your bike, but the 954 is one of a few models that we know has some interference issues when using them in a street bike application. |
|
| QUESTION: Will this if on a 2004 Ducati Monster 620 ie? |
| ANSWER: They will fit on the forks. Actual fitment needs to be determined by the end user. |
|
| QUESTION: Will these fit a 2005 ZX6r (636)? |
| ANSWER: Yes, they will. |
|
| QUESTION: WHAT stock item,clip on for cbr929rr |
| ANSWER: These will physically fit on this model, but we are aware that 929's have interference with OEM parts if this is a street application. If this is a street bike - I do not know of any aftermarket clipons that are a simple bolt on installation. |
|
| QUESTION: I have a 04 gsrx1000 and i would like to buy clip on risers.. do these work. and how much higher will my bars be.. |
| ANSWER: We do not make risers, these are performace/race parts. |
|
| QUESTION: are these the right ones for an 04 zx636? what ange are the stock bars? |
| ANSWER: Yes, and they are very close to the angle of the stock bars (within a degree)....the OEM companies have the ergo's worked out pretty well on modern 600's. |
|
| QUESTION: Are these 50mm bars the correct fit for my Suzuki TL1000R?........and how much further can it raise the stock height for a more comfortable ride? |
| ANSWER: These will fit your bike - but are not made for a "comfortable" ride.....these are race parts that will give you more control and better from end feel, but are not higher than OEM. |
|
| QUESTION: Will these fit on a 1997 Aprilia RS250. It show they do in one application chart but not the other? |
| ANSWER: The 50mm clipons fit all years Aprilia RS250. |
|
| QUESTION: Hello, I would like to buy a clip on (handlebar risers). I have a 2004 GSXR1000.
Thanks, Joe |
| ANSWER: You will need our clipons designed specifically to fit the GSXR1000 '01-04 fork tubes #12-0250 50/49. They are 50mmm with approx. 1/4" at the bottom of the clamp sleeved down to 49mm. The new GSXR1000 takes the regular 50mm clipons. |
|
| QUESTION: Will the 2005 suzuki gsx-r1000(k5) clip-ons work for street use?
I broke my right side, are they available individualy? tx |
| ANSWER: Our clipons are designed primarily for road racing. The 05 GSXR1000 takes straight 50mm clipons. Our product is a 7 degree angle, the clamps are 1-1/2" high/wide the bars are 1' long. They are sold as a set only, although replacement bars can be purchased separately. I'm not sure how the stock/street bodywork is but I don't think there are interference issues on this bike. You should take this information and see if they will work for you. |
|
| QUESTION: I would like to purchase some Woodcraft Race Clip-on but don't know what size would fit my 05' Triumph Speed triple.
Please help.
|
| ANSWER: To the best of our knowledge most Triumphs take 45mm clipons. It would be best for you to check with your local Triumph dealer. Make sure you know you need the fork measurement at the top end of the tube. |
|
| QUESTION: Will these 50mm fit my 05' Ducati S4R? Do I need anything else or can I just mount these on and be on my mary way? |
| ANSWER: You can install these and be on your merry way. |
|
| QUESTION: I am interested in these Clip ons for 04' CBR 1000RR, can these bars be reliable for race use? If so, what other degree angles can be attained with these? |
| ANSWER: These have been used PRIMARILY for racing for nearly 6 years. 7 degrees is comfortable for racing and there are literally thousands of racers using them. |
|
| QUESTION: Is there any angle on these clip ons? If so, what degree.. Thanks |
| ANSWER: The angle is 7 degrees which is the same as stock. |
|
| QUESTION: if send to singapore how much ?
for suzuki gsx-r 1000 K3 .
thanks best regards |
| ANSWER: It costs $53.00 to ship a 2 lb. package to Singapore. We need to know what year the Suzuki GSXR1000 (K3) and if the bike is used for racing or street riding. Our 2 piece clipons #12-0250 are specifically designed to fit the tapered GSXR1000 fork; however we've been informed 2003-04 stock bodywork (street riding) has some interference in a full lock turn. Road racers have different bodywork and do not mind making minor modifications to fit.
Jan - Customer Service |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Schdeule
powered by WordPress e-commerce company