|
| Rear Pad Stand |
Low Lift Effort & easy adjustability
Super Stable quad 4 inch Wheels that roll over almost anything
Super tacky swingarm pads to avoid slippage
Not Available for International Shipping |
| |
| Item no.25-0200 |
| Today$170.95 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| super
tacky pad lift Stand
|
WORK
CLEARANCE
Mechanics appreciate
both the easy lift
effort and ample working clearanace behind
the stand - workseat clearance is excellent
behind the rear wheel!!
POWERCOAT
FINISH
Woodcraft stands have one
of the toughest, most expensive powder coat finishes available
today.
|
Super
Tacky
Stand Pads
Our pivots have SUPER
TACKY rubber pads that prevent slippage.
Big Diameter, Smooth Operating
Pivots
1"
diameter solid steel lift pivots that roll smoothly and
won't bend or break like other stands. The inner
portion of the stand is teflon lined to keep operation smooth.
|
XL WHEELS
Woodcraft's trademark
extra large quad 4" wheels are extremely stable and
facillitate both lifting the bike on rough surfaces and
rolling the bike around the shop!!
FAST, EASY WIDTH ADJUSTMENT
With a pair of pliers, the
width of the Woodcraft RS102 can be adjusted in seconds!!
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: Hi, I have a 2002 750 katana. it doesn't have any spool holes. is the whidth of this stand will fit the bike?
thanks |
| ANSWER: Yes, it definitely will. |
|
| QUESTION: i have a 2006 GSXR1000 would this stand work? |
| ANSWER: Yes, but the spool stands are always my first choice. But again, this will work if it's what you'd like |
|
| QUESTION: Hi, will this fit a 06 CBR 600RR, Thanks |
| ANSWER: It will - but I would definitely recommend the 25-0100 instead. You need 8mm spools to go with it. Spool stands are always the first choice. |
|
| QUESTION: Will this stand work on my 2003 Buell XB9S? |
| ANSWER: Yes, it will |
|
| QUESTION: Do I need spools for this for a 2003 r6?? If so what size?? |
| ANSWER: Yes, 6mm. However, this is not the ridght stand for you - you need the 25-0100 spool stand. |
|
| QUESTION: will this fit a 1996 zx9r? if so what is recommended for swingarm spool/slider? |
| ANSWER: Yes, but we would strongly recommend the 25-0100 spool stand instead, together with the spool sliders. Check your swingarm to see if the spool receivers are inset or not, 27-3100 for no insets, 27-3110 for 1 side inset, 27-3120 for both sides. |
|
| QUESTION: Will this work on a 240 fat tire swingarm for my Busa..?? |
| ANSWER: I dont know.....the stand is set up at 14" wide. If you have spools, you can safely expand our standard 25-0100 stand to at least 15 inches by setting it on its side and pulling it out wider. These stands are made from a material that is meant to do this and they hold their shape very well. |
|
| QUESTION: will this work on the front tire also |
| ANSWER: No, this is for the rear only |
|
| QUESTION: Hi, will this stand work for a 99 cbr600f4? thanks |
| ANSWER: Yes, it will |
|
| QUESTION: does this stand fit a '94 fzr 600? |
| ANSWER: Yes, it will |
|
| QUESTION: Hello, will this stand work with my 2004 Honda 599? I did not see 8 mm bolt holes where spools could be used. |
| ANSWER: Yes, this stand shoud work perfectly on your bike. |
|
| QUESTION: will this stand work for my 01 CBR 600 F4I? |
| ANSWER: Yes, it will |
|
| QUESTION: Willl this fit the ZX14? |
| ANSWER: Yes, but I would suggest that you look at the spool stand - 25-0100, and a set of spools (27-3120)....you'll be happier in the long run with that setup. |
|
| QUESTION: I need a stand for my 2006 Suzuki GSXR750. Will this stand work? |
| ANSWER: It will work, but I would highly recommend the 25-0100 spool stand. Always use spools whenever you can, the stands are much easier to work with |
|
| QUESTION: I was wondering if this would work with my 2006 Kawasaki ZZR600. Thanks. |
| ANSWER: Yes, it will, but I would advise using a 25-0100 spool stand and a set of ZX6r spools - that is the best way to go for that bike |
|
| QUESTION: Will this fit my new 2006 Triumph Speed Triple with single side swing arm? I want the solo front stand too. Will this fit my Speed Triple? Lastly, is the free freight offer good for Zip code 96825? |
| ANSWER: No all our stands are designed for dual, equal level swingarms. |
|
| QUESTION: Do you have this in stock now |
| ANSWER: Hi,
We will have it in stock mid-month. Thanks. Jan - Customer Service |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Schdeule
powered by WordPress e-commerce company