|
|
|
|
| Application Chart |
Diagrams |
Application
Notes |
|
| 1994 Kawasaki EX 500 |
|
|
| 1995 Kawasaki EX 500 |
|
|
| 1996 Kawasaki EX 500 |
|
|
| 1997 Kawasaki EX 500 |
|
|
| 1998 Kawasaki EX 500 |
|
|
| 1999 Kawasaki EX 500 |
|
|
| 2000 Kawasaki EX 500 |
|
|
| 2001 Kawasaki EX 500 |
|
|
| 2002 Kawasaki EX 500 |
|
|
| 2003 Kawasaki EX 500 |
|
|
|
|
|
|
|
|
|
|
|
|
|
Why buy a BRAKE PRESSURE SWITCH ASSY? Coarse or Fine?
These universal switches allow rearset users to operate the rear brake light. This all-in-one unit replaces the banjo bolt that connects the rear master cylinder to the rear brake line. You simply replace the bolt with this assembly and splice the wires into your existing brake light switch. The pressure inside your brake system then activates the brake light.
This part is a MUST HAVE item if you are going to ride your Woodcraft Race Rearset equipped bike on the street. Woodcraft Race Rearsets do NOT have a mount for your brake light switch linkage. This switch comes with a replacement banjo bolt and a pressure sensor switch that senses when pressure is applied, and triggers your brake light.
The thread pitch can vary between different bikes IN THE SAME MODEL YEAR. Please make certain which thread pitch your specific bike has before ordering.
NO RETURN OR REFUND ON THIS ITEM!
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: will i have to cut away at the sprocket case unless i use a reverse shift pattern |
| ANSWER: No, there is no cutting needed. For GP shift you need to buy a different shift pedal, but everything else is the same. |
|
| QUESTION: do you have any pics of the rear set |
| ANSWER: Check here - http://www.woodcraft-cfm.com/Scripts/prodView.asp?idproduct=17545 |
|
| QUESTION: will these rear sets work for a 06 ex500r? or do you have any that will work |
| ANSWER: They shold work on all EX500's 94 and newer. |
|
| QUESTION: Do I need a new shift rod with these? If so, do they come with the new shift rod? |
| ANSWER: The kit does require a rod, which is included in the kit. |
|
| QUESTION: will this fit the 04 ninja 500 r and can u use the stock brake and shift pedals and if not do u sell them and how much |
| ANSWER: All of our basic rear set kits are designed to work with OEM shift and brake pedals unless specifically noted otherwise. We do not offer our three piece shift and brake pedals for the model so you will utilize the stock ones. |
|
| QUESTION: what would the rearsets do for my bike? |
| ANSWER: Primarily, they will offer much greater ground clearance as well as increased rider mobility on the motorcycle. They also look quite a bit nicer than the stock units. |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Schdeule
powered by WordPress e-commerce company