|
| Honda CBR 600 RR Woodcraft Left Side Case Cover |
Note: This engine cover does not come with a gasket. Please use a semi drying liquid gasket (Yamabond or similar) not supplied.
|
| |
| Item no.60-0335L |
Retail: $199.99(PLUS shipping) |
| Today$195.95 |
|
|
|
|
| Application Chart |
Diagrams |
Application
Notes |
|
| 2003 Honda CBR 600 RR |
|
|
| 2004 Honda CBR 600 RR |
|
|
| 2005 Honda CBR 600 RR |
|
|
| 2006 Honda CBR 600 RR |
|
|
| 2007 Honda CBR 600 RR |
|
|
|
|
|
|
|
|
|
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: No, but we do have the 2007 model in stock. It is an alternator cover.
whats the part# so i can order?
|
| ANSWER: 60-0338LB |
|
| QUESTION: i need a part # for the alternator cover for 2007 hond cbr 600 rr |
| ANSWER: 60-0338LB |
|
| QUESTION: does this fit a 2007 honda cbr 600rr? is this the alternator cover |
| ANSWER: No, but we do have the 2007 model in stock. It is an alternator cover. |
|
| QUESTION: How long would it take to get one? Your competitors have a 6 week wait on them and I have a race in 3 weeks. Thanks |
| ANSWER: We have clear (silver) and black anodized covers on the shelf. |
|
| QUESTION: how hard is it to change te pads |
| ANSWER: It is not too hard. First of all depending on the model bike you may be able to lean it so there is only a minimal amount of oil lost while removing the cover. If that is not the case either way you will have to check the oil level afterwards and replace any oil lost while working. Remove the skid plate and the hardware/o-rings. You will probably have to use a torch or heat gun because they are installed with permanent Loctite or Permabond. Clean everything up well so there will be a good seal. Replace with the new skid plate and NEW hardware/o-rings and tighten down bolts to industry standard torque. If you are not comfortable doing this take your bike to a franchised dealer or performance shop. |
|
| QUESTION: what are the benifits to have this type of casing? and are you able to ship the casing to Canada and |
| ANSWER: It is made from billet and will not break in the event of a crash. It also in much better looking than your stock cover, and has a replaceable skid pad to keep the cover looking good after a crash. Please ask 1tail about Canada shipping |
|
| QUESTION: When will the LH side case cover for the 2005 CBR1000RR be available? Need one immediately for the CA racing season. |
| ANSWER: We have it designed and it will be produced very soon, maybe 4 weeks out. Stay tuned. |
|
| QUESTION: Do these covers come with replacement gaskets? |
| ANSWER: Honda CBR600RR does not use a gasket. It requires the use of "Yamabond" or an equal gasket forming compound which we do not supply. Jan - Customer Service |
|
| QUESTION: does this case fit the 2004 cbr 600f4i? |
| ANSWER: No, only the new RR....thanks |
|
| QUESTION: Do you have a cover that fits a 03 954RR left side |
| ANSWER: No sorry we do not. Although we've had some inquiries there is not enough demand to warrant the design and production thereof. Thanks for the inquiry. Jan |
|
| QUESTION: do you sell the right side? |
| ANSWER: Not yet. If we do decide to make it that will not happen until this fall. Sorry, but the plate is full! Woodcraft |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Schdeule
powered by WordPress e-commerce company