|
| 8mm SWINGARM SLIDER SPOOLS (set of 2) |
Make the most of your rear stand!! Woodcraft swingarm spools are designed wide for easy stand location with raised lips on their outer edges for security. Your stand will work even better when coupled with these spools.
These spools are made from solid black delrin and have a fully supported Aluminum core to give them extra strength
|
| |
| Item no. 27-3800 |
Retail: $29.99(PLUS shipping) |
| Today$26.95 |
|
|
|
|
|
|
|
|
|
|
|
|
| This item does NOT ship for free |
| Shipping charges will apply to this item. If you place your order now we will call with the shipping rate. If the rate is approved by you we will charge you the additional shipping. If the rate is NOT approved by you then we will cancel your order. If you do not wish to place your order now you can enter in the quantity you wish to order and your zip code in the Q&A section below and we will respond with a quote. |
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: will this fit a 2007 zzr600? |
| ANSWER: No, you would need 10mm spools with 1 step. |
|
| QUESTION: IS THERE A WAY TO INSTALL THESE ON A 2006 CBR F4I |
| ANSWER: Where there's a will, there's a way. You would have to weld lugs on the bottom of the swingarm. If it were my bike and I planned to keep it for a while, I'd consider it as spool stands are always the best bet....but that's your call. |
|
| QUESTION: Is there a way to install these on a 2002 Honda CBR929? |
| ANSWER: There is always a way.....but on your bike it would involve welding an aluminum lug to the bottom of the swingarm. |
|
| QUESTION: So these would fit 2008 honda cbr600rr?? |
| ANSWER: Yes but they need a spacer, which we have, to work with your specific bike. |
|
| QUESTION: What is the dimension of the center portion?
My stand has a little cradle for the spools and I need to know if it'll fit in there. |
| ANSWER: The center diameter is .580 |
|
| QUESTION: do these fit 07 hayabusa? thanks |
| ANSWER: They should, Although I have not seen the Busa, every Suzuki for the past 10 years has used 8mm spools |
|
| QUESTION: can you get these in anodized blue? if not can you attach the blue woodcraft pucks to these? |
| ANSWER: Yes, they are avaialble in blue and you can get sloder tops to match. |
|
| QUESTION: will these fit my 2007 GSXR and how easy are they to install |
| ANSWER: Yes, it takes about 60 seconds to install them. |
|
| QUESTION: Are this for stands or are they sliders also?
|
| ANSWER: These are stand spools that also act as sliders |
|
| QUESTION: Is this ok for a gsxr600 k6. Cheers. |
| ANSWER: Yes, they will work on almost all GSXR's |
|
| QUESTION: Are these 8x1.25 thread? ducati 999R fitment |
| ANSWER: Yes, they are standard 8mm thread - if your swingarm is tapped with 8mm holes (not all 999's are) then these will fit. |
|
| QUESTION: Is this the right size spool for a 01 cbr 600 f4i? |
| ANSWER: If your bike has a place to receive swingarm spools, all Hondas are 8mm. I am not sure if every F4 had them, so check your bike to be sure. |
|
| QUESTION: hi, would these spools fit a ducati 999?... and what would the carge be for shipment to sydney, australia? |
| ANSWER: Yes, they will fit - but for shipping to Autralia please contact 1tail |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Schdeule
powered by WordPress e-commerce company