|
| 6MM SWINGARM SLIDER SPOOLS (set of 2) |
Make the most of your rear stand!! Woodcraft swingarm spools are designed wide for easy stand location with raised lips on their outer edges for security. Your stand will work even better when coupled with these spools.
These spools are made from solid black delrin and have a fully supported Aluminum core to give them extra strength
|
| |
| Item no. 27-3600 |
Retail: $29.99(PLUS shipping) |
| Today$26.95 |
|
|
|
|
|
|
|
|
|
|
|
|
| This item does NOT ship for free |
| Shipping charges will apply to this item. If you place your order now we will call with the shipping rate. If the rate is approved by you we will charge you the additional shipping. If the rate is NOT approved by you then we will cancel your order. If you do not wish to place your order now you can enter in the quantity you wish to order and your zip code in the Q&A section below and we will respond with a quote. |
|
|
|
| WARNING: Laws concerning this product vary from state/province to state/province. Your state/province may prohibit its use on public roads or restrict its use to novelty, show use, off-road areas, or race facility areas only. In some states/provinces off-road uses are also prohibited. The manufacturer and retailer assume no responsibility for any use or application of this product in violation of any applicable law. Before installing this product, please check your state/provincial and local/municipal laws and regulations. |
|
| The Q&A on this Product |
|
|
| QUESTION: Will these fit a kawasaki ZX6E 2002 model? |
| ANSWER: No Kawi's take 10mm spools |
|
| QUESTION: What is a pad stand? |
| ANSWER: A stand the lifts simply by the bottom of the swingarm (on pads) rather than hooking on to spools. |
|
| QUESTION: WILL THESE FIT A K5 GSXR-1000? 6MM OR 8MM? PLEASE RESPOND! |
| ANSWER: No, GSXR's definitely need 8mm |
|
| QUESTION: Will these fit a 2002 FZ1 |
| ANSWER: No, your bike does not appear to have a location for the 6mm spools on it. You can look yourself, but I could not see one in the pictures I found. If that is the case you'll need a pad stand. |
|
| QUESTION: Are these the right ones for a '07 Triumph Daytona 675? Thanks in advance. |
| ANSWER: Yes, the 675 uses 6mm spools. |
|
| QUESTION: Will these fit a 2008 R6 |
| ANSWER: Yes |
|
| QUESTION: i have a 2007 fz1... will these fit? is the 6mm the statndard spool size for all yamaha bikes? |
| ANSWER: For the newer ones, yes - 6mm is the Yamaha standard and this is what fits the FZ1. |
|
| QUESTION: Will these fit an 05 ZX-6R? |
| ANSWER: No, defintely not. The Kawasaki's take 10mm spools, and I believe that the ZX6R has an offset on one side. You would need the 27-3110 spool sliders. |
|
| QUESTION: I have a 2006 gsxr600 would these fit |
| ANSWER: Yes, 8mm is the right size |
|
| QUESTION: I have a 1999 r6 would these fit ? |
| ANSWER: Yes, they will |
|
| QUESTION: I have a 2002 R6 will these fit? thanks |
| ANSWER: Yes |
|
| QUESTION: I have a 2005 R6 and i was just wondering if these would fit on my bike before i go ahead and order them. |
| ANSWER: Yes, these will fit. |
|
|
|
| Ask your question here: |
|
| Your email (so we can send you the answer): |
|
|
|
Event Schdeule
powered by WordPress e-commerce company